Author Topic: Whirlpool direct drive agitates but no spin  (Read 8310 times)

Offline philhyde

  • VIP Member
  • Member Since: Aug 2007
  • Posts: 18
Re: Whirlpool direct drive agitates but no spin
« Reply #15 on: October 04, 2007, 08:26:44 AM »
Quote
After the water all drains out there should be another pause were the motor stop running. Then the motor should kick in again and the washer should spin.

Yes, I did observe this.  But no spin.

Quote
What is the model number of your washer?

LSQ9520LQ0

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9478
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Whirlpool direct drive agitates but no spin
« Reply #16 on: October 04, 2007, 09:47:23 AM »
Sounds like the timer is doing it's job with the correct pauses.

Looks like it's time to replace the tranny.

Here is the one you would need for your washer.


Please keep us updated as to what you decide to do.
If you need help replacing the tranny we could help you with any problems you may run into.

It's not to hard of a job. Takes me about 20 minutes to put one in. That's if I have enough room to work and everything comes apart ok.

Being yours is not all that old I would think it would come apart easy enough.



Hope you find our site helpful.

Offline philhyde

  • VIP Member
  • Member Since: Aug 2007
  • Posts: 18
Re: Whirlpool direct drive agitates but no spin
« Reply #17 on: October 04, 2007, 10:09:41 AM »
Not a cheap part.  But I guess, cheaper to put in myself!

Is the part going to have installation instructions?  I'm pretty handy, and would guess that upon unbolting it would be obvious.  Is this correct?

Thanks!  :)

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9478
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Whirlpool direct drive agitates but no spin
« Reply #18 on: October 04, 2007, 10:46:38 AM »
Quote
Is the part going to have installation instructions?]

No instruction with it. I think the hardest part for anyone that has never done one before will be moving the clutch over from the top of the old tranny to the new one. Then you will have to make sure the clutch goes into the brake correctly when you slide the tranny back up into the washer.

Other then that all you have to do is remove the agitator. The agitator is the only thing you have to remove from the top of the washer.

Then remove the cabinet, lay the washer on it's back. I often lay the washer on the tranny box so what little water is in the washer does not run all over the place.

Even if all the water is pumped out there is some in the pump and if you lay it on flate on it's back water will run out the top of the tub and onto the floor.

Remove the pump from the motor, you can leave the hoses on the pump. Then remove the motor. Then the tranny will have three bolts that hold it in.

Remove the three tranny bolts and slide it out.

I have heard other say you don't have to grease the new tranny shaft, but I alway's put just a little bit of grease on it. I use some high temp bearing grease.

Just very little grease and don't get it on the clutch.

If you need more help once you get it and can try and post some more details with photo. Maybe even get a video posted if I do a tranny job between now and then. :)
« Last Edit: October 04, 2007, 12:46:13 PM by AJ »
Hope you find our site helpful.

Offline philhyde

  • VIP Member
  • Member Since: Aug 2007
  • Posts: 18
Re: Whirlpool direct drive agitates but no spin
« Reply #19 on: October 04, 2007, 12:32:52 PM »
Thank you for all of the assistance.

 

Repair Guide: Whirlpool Direct Drive Washer - No agitate or spin

Started by AJ

Replies: 13
Views: 28831
Last post January 02, 2009, 01:09:38 PM
by AJ
Whirlpool direct-drive washer will not spin, then will if turned by hand slightl

Started by alaball

Replies: 2
Views: 2864
Last post May 29, 2009, 10:11:07 PM
by alaball
whirlpool direct drive washer won't spin

Started by viking351

Replies: 14
Views: 5782
Last post June 26, 2009, 05:57:27 PM
by viking351
Whirlpool direct drive washer won't spin

Started by CT Jayson

Replies: 18
Views: 9393
Last post July 02, 2009, 09:36:13 PM
by whirlpooltech
Whirlpool direct drive washer won't spin

Started by fsimcox

Replies: 2
Views: 3053
Last post November 14, 2009, 05:34:17 AM
by apprich
Maytag and Whirlpool Front Load Direct Drive Washers - No Spin or Wet Clothes

Started by AJ

Replies: 0
Views: 2320
Last post March 14, 2011, 12:04:13 AM
by AJ