Author Topic: Whirlpool clutch went bad again.  (Read 419 times)

Offline Xfile69

  • VIP Member
  • Member Since: May 2013
  • Posts: 2
Whirlpool clutch went bad again.
« on: May 21, 2013, 08:28:01 AM »
OK i read quite a few places on what would make the washer make it not spin, so i replaced a few things to fix it. I replaced the connector from the motor to tranny didn't need it. Replaced the 4 knobs to the agitator so could connect better on the agitating the water it needed it. Then i replaced the clutch on the tranny to the drum since the clutch i could easily move with one finger around. Now it seem to work just fine but after a few loads no go anymore seem the clutch went bad again i can tell this since took it back apart can move with one finger again. Now i can tell it wasn't just a bad clutch do to the fact that all the shaving around the clutches shows me that it was just wore down so fast. What would make the clutch go bad that fast yes i did do one heavy load but shouldn't killed it after 4 loads (only 1 heavy load). From the bottom of the washer with the tranny off i can turn the plastic thing to turn the drum left and right.

Offline Xfile69

  • VIP Member
  • Member Since: May 2013
  • Posts: 2
Re: Whirlpool clutch went bad again.
« Reply #1 on: May 21, 2013, 08:50:23 AM »
oh one other note i did just try to hoot the drill to motor shaft forward and reverse and it seem to be catching just fine tried to stop it from moving and couldn't in the one direction. in the other it just move back and forth like the agitator is to move.

Offline fairbank56

  • Technician
  • Member Since: Aug 2012
  • Posts: 359
  • Country: us
Re: Whirlpool clutch went bad again.
« Reply #2 on: May 21, 2013, 09:28:27 AM »
  Did you buy a genuine Whirlpool FSP clutch? There are clutches being sold on ebay and amazon for $8 and they are junk, will only last a few loads before wearing out. You should only be able to rotate the brake cam driver counterclockwise which releases the brake and allows rotation of the basket drive. If you can rotate it clockwise, the brakes aren't doing their job.

Eric
« Last Edit: May 21, 2013, 09:31:02 AM by fairbank56 »

 

Video: Whirlpool Direct Drive Washer Clutch, Brake Transmission - Gear Case

Started by AJ

Replies: 6
Views: 12074
Last post January 26, 2008, 08:15:30 PM
by RegUS_PatOff
285785 Whirlpool Washer Clutch

Started by AJ

Replies: 0
Views: 5524
Last post March 08, 2009, 11:06:18 AM
by AJ
replace whirlpool clutch

Started by viking351

Replies: 3
Views: 1472
Last post August 18, 2009, 04:05:42 PM
by viking351
Video: Whirlpool Washing Machine Clutch Replacement

Started by AJ

Replies: 1
Views: 3492
Last post June 19, 2010, 07:45:13 PM
by jomi
Whirlpool gearcase/clutch/spin tube question (ATTN: Repair-man)

Started by landlady

Replies: 6
Views: 2987
Last post February 14, 2011, 08:17:00 PM
by landlady
Replacing Whirlpool direct washer clutch - C clip flew off and can't find it!

Started by jamesve

Replies: 9
Views: 2690
Last post June 11, 2011, 11:03:57 AM
by jamesve