Author Topic: Kenmore electric dryer no heat  (Read 3534 times)

Offline pcornelius

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 5
Kenmore electric dryer no heat
« on: May 28, 2008, 05:09:52 PM »
Dryer works but has not heat. Checked the Thermal Fuse and it is reading 15.9 Ohms and on the Diode testing it is getting a beep meaning it is not broken within. Heating element shows 11.1 on the reading and the High thermostat shows 1.6. The thermal Cutout has no reading and on the diode tester I get no beep. I see that it is not resetable so I assume it is like a fuse. The main wiring block all looks good. Please adivse if it will be the Thermal Cut out or if the door switch will cause it to have no heat if bad.  BTW, the breaker box I reset and it still has no heat

Model 110.94678100
« Last Edit: May 28, 2008, 06:18:41 PM by Al Capone »

Offline Penguin45

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 81
    • www.ukwhitegoods.com
Re: Kenmore electric dryer no heat
« Reply #1 on: May 28, 2008, 06:51:33 PM »
Sounds like you need this little chappie HERE.

Penguin45.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore electric dryer no heat
« Reply #2 on: May 30, 2008, 09:36:52 AM »
if your thermal cutout mounted at the top of the element s heat chamber has no continuity then replace it. That is the problem.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kenmore electric dryer no heat
« Reply #3 on: May 30, 2008, 11:44:50 AM »
check those measurements again...and check your meter (short the meter leads together to see if it reads 0 OHMS)

The Thermal Fuse, Thermal Cutoff, and the Hi-Limit Thermostat should all read 0 OHMS.

and check that model number again...can't find anything on 110.94678100


« Last Edit: May 30, 2008, 11:48:51 AM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

 

Kenmore 70 series electric dryer...wont heat

Started by lalakelley

Replies: 53
Views: 34439
Last post November 24, 2011, 02:40:03 AM
by RegUS_PatOff
70 series Kenmore electric dryer spins but does not heat

Started by llew_x

Replies: 52
Views: 37231
Last post July 23, 2013, 08:25:04 AM
by JWWebster
Kenmore 70 series electric dryer no heat again

Started by weadhopper

Replies: 5
Views: 3900
Last post May 14, 2009, 11:13:08 PM
by JWWebster
Kenmore 70 series electric dryer no heat again

Started by connie

Replies: 10
Views: 3033
Last post June 09, 2009, 05:59:07 AM
by connie
Kenmore 70 electric dryer no heat

Started by craigb

Replies: 2
Views: 1373
Last post June 11, 2009, 01:49:57 PM
by craigb
Kenmore 70 Series Electric dryer wont heat up

Started by Paco taco

Replies: 4
Views: 6134
Last post December 29, 2009, 11:32:31 AM
by whirlpooltech