Author Topic: Kenmore 70 series electric dryer...wont heat  (Read 41366 times)

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #40 on: May 28, 2008, 10:57:04 PM »
Im going to go to bed now...will you be on tomorrow?!

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kenmore 70 series electric dryer...wont heat
« Reply #41 on: May 28, 2008, 11:00:04 PM »
I don't know about that other wire..

I may be here sometime tommorrow, other someone else may be around...

Also, check the voltage at the (3) terminals on the back of the dryer.

120v from each of the OUTER ones to CENTER
240v across OUTER ONES

With power cord unplugged, check to see if the terminals are tight.

« Last Edit: May 29, 2008, 06:39:18 AM by RegUS_PatOff »
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Kenmore 70 series electric dryer...wont heat
« Reply #42 on: May 28, 2008, 11:32:53 PM »
Can you post some photos of what your looking at and what your testing?

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #43 on: May 29, 2008, 08:08:40 AM »
I could do that tonight hopefully...I'm at work right now, so I'm not near the dryer to test anything on it nor can I take pic :) But I will do what I can tonight...My hubby is to the point that he wants to just replace the thermal fuse and be done with it, but if that is not the problem then it won't work :-/

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #44 on: May 29, 2008, 08:44:35 AM »
We tested the wires connected to #34 in this picture...since i am not home to take the pic I figured I'd use this one :)

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #45 on: May 30, 2008, 05:49:53 PM »
Ok, UPDATE...My husband never tested those last things you suggested but has given up on all the test...he left to go get a new fuse and thermostat...he will be putting them in tonight so I will let you know how it works :)

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8781
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore 70 series electric dryer...wont heat
« Reply #46 on: May 30, 2008, 09:47:20 PM »
#1 is likely gone bad as pictured. Luckily both 34 and number 1 come in the same package and they recommend both get replaced. Why? Because 34 is a 250f degree limit(resetable internally) and #1 is a 300f degree limit non-re-setable, Obviously the number 34 klixon failed to do it's job or more likely did it's job till it died due to poor venting problems or faulty control thermostats.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #47 on: May 31, 2008, 07:41:59 AM »
WELL...that didn't work, so today he is going to go get a new heating element, the thermal fuse and the other thermostat that is near connected into the vent housing thing. We figure this is going to work cause after that point we will have replaced almost everything on the dryer and have olmost a new dryer :)

Offline Earl Dryer

  • Technician
  • Member Since: May 2008
  • Posts: 166
  • Country: us
Re: Kenmore 70 series electric dryer...wont heat
« Reply #48 on: June 01, 2008, 03:51:24 PM »
Try this, I've had these small elements drive me crazy because they
test good but they are fused. Clip the test leads on each of they element terminals, set the OHMMeter to show a mid scale reading then gently shake the element back & forth up & down watch the
meter. I have 2 in the last month that were fused but would close back up when the cooled then open when they began to heat.

Offline lalakelley

  • VIP Member
  • Member Since: Feb 2008
  • Posts: 35
Re: Kenmore 70 series electric dryer...wont heat
« Reply #49 on: June 02, 2008, 08:28:10 AM »
UPDATE  ;D He went to Sears on Saturday, to buy the thermal fuse(which they didnt have) other thermostat(which the didnt have either) and heating element(they had this). When he got home he replaced the heating element and the dryer works GREAT. Better than when we first bought it :) Thank you though for all your help


WHIRLPOOL 279838 Whirlpool Dryer Heating Element, AP3094254



 

Kenmore 70 Series Electric dryer wont heat up

Started by Paco taco

Replies: 4
Views: 7818
Last post December 29, 2009, 11:32:31 AM
by whirlpooltech
Kenmore 70 Series Electric dryer wont heat up

Started by kid_sketch

Replies: 22
Views: 8879
Last post January 21, 2010, 09:36:42 PM
by AJ
70 series Kenmore electric dryer spins but does not heat

Started by llew_x

Replies: 52
Views: 47773
Last post July 23, 2013, 08:25:04 AM
by JWWebster
Kenmore 70 series electric dryer no heat again

Started by weadhopper

Replies: 5
Views: 5648
Last post May 14, 2009, 11:13:08 PM
by JWWebster
Kenmore 70 series electric dryer no heat again

Started by connie

Replies: 10
Views: 4748
Last post June 09, 2009, 05:59:07 AM
by connie
Kenmore 80 Series Electric Dryer won't heat

Started by snottrocket

Replies: 8
Views: 15501
Last post June 06, 2011, 09:35:10 PM
by JWWebster