Author Topic: Is thier an easy way to test for shorts.  (Read 706 times)

Offline itsastarr

  • Technician
  • Member Since: Mar 2012
  • Posts: 37
Is thier an easy way to test for shorts.
« on: May 05, 2013, 09:35:44 AM »

  I was hoping someone  would know of  a video , book  or any resource  I could find  to  instruct me on

   how to find where  a short would be coming from?   :thanks:

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9331
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Is thier an easy way to test for shorts.
« Reply #1 on: May 05, 2013, 10:29:15 AM »
When looking for shorts it's often just a visual thing. Like seeing a wire nut that burnt off and the wire is touching the metal frame of the appliance causing a short.

Other times I find them just by using some common sense and experience. Say for example if you have a heating element on a dryer that is shorted to the case. I would know where to look by the way the dryer was acting. In this case I could use my multimeter to check for continuity between the dryer element spades and the case to see if it was shorted. 

Maybe some other members could post some tips for us too.

Hope you find our site helpful.
Follow us on Google+

Offline Specialist

  • Technician
  • Member Since: May 2012
  • Posts: 132
  • Country: gb
  • Electrical Appliance / Catering Equipment Engineer
    • Buy me a beer through paypal
Re: Is thier an easy way to test for shorts.
« Reply #2 on: May 05, 2013, 10:52:22 AM »
As AJ says a lot of it is down to experience of different appliances. For example with a washing machine blowing a breaker, if it does it straight away when plugged in then you'd go to the mains filter first & disconnect that. Then it's a quick job of testing with a Multimeter or Megger to find if it's shorted or not, if not then you move to the next item in the line & do the same thing. If it's dropping the breaker further into the programme then work out what should be coming in then, i.e Inlet valve, Pump, Heater etc & disconnect / test that part. Just a process of elimination.
Let Us Fix It Properly.

Offline go400

  • Technician
  • Member Since: Feb 2013
  • Posts: 285
  • Country: us
Re: Is thier an easy way to test for shorts.
« Reply #3 on: May 05, 2013, 01:03:36 PM »
If a dryer, and it blows the breaker right when you plug it in, it's the heating element shorted. If anything else, you have to determine
what the item was switching into when it blew. If a refrigerator and you turn the defrost timer to defrost and it blows the breaker, the short is in the defrost circuit.
 If a washer or fridg. would be helpful to put it on a extension cord with breaker.
 Sometimes you can find a short with an ohmmeter. Most of the time though, the short only happens when you put 115 volts to the item, 9 volt ohmmeter will not indicate
a short in that case.

donate
$1, $2, $5, $10, $20, $50
 

Special Appliance Repair Tools and Test Equipment

Started by AJ

Replies: 1
Views: 3994
Last post November 16, 2007, 08:40:52 PM
by AJ
How to use Test Equipment

Started by AJ

Replies: 2
Views: 1822
Last post September 20, 2008, 10:56:57 AM
by whirlpooltech
Bad light switch? Easy to replace?

Started by terry

Replies: 3
Views: 2478
Last post February 08, 2013, 04:21:53 PM
by SmArtE
Part 1 of diagnoses test

Started by bakeray

Replies: 1
Views: 1066
Last post March 24, 2010, 11:47:03 AM
by AJ
Pin connector test board.

Started by schaffersapplian

Replies: 17
Views: 4210
Last post June 13, 2010, 11:30:36 AM
by brad
MOVED: Sears Basic Electric Test

Started by AJ

Replies: 0
Views: 496
Last post November 19, 2013, 05:00:29 PM
by AJ