Author Topic: MAYTAG WASHER MODEL MVWC450XW  (Read 1083 times)

Offline gregaguilar

  • Technician
  • Member Since: Jan 2012
  • Posts: 95
MAYTAG WASHER MODEL MVWC450XW
« on: April 22, 2013, 11:57:46 PM »
I AM WORKING ON A MAYTAG TOP LOAD WASHER MVWC450XW THE PROBLEM IS THAT WHEN I ENTER THE CALIBRATION  THE MOTOR WILL HUM AND THEN THE LID LED COMES ON FLASHING. WELL I CHECKED EVERYTHING ON IT THE LID SWITCH THE SHIFT ACTUATOR THE SLUTCH AND THE CONTROL BOARD HAS POWER. I CHECKED THE MOTOR AND AND NOTED THE WINDINGS FROM PIN 3 TO 9 WAS OVER THE 6 OHMS ANYWAY I TOOK THE MOTOR 20 MILES INTO THE SHOP AND I INSTALLED THE MOTOR ON A SIMILAR WASHER AND IT WORKED FINE NOW TOMORROW I AM GOING OUT THE CUSTOMERS HOME 20 MILES AWAY AND I AM GOING TO CHECK THE WIRES FROM THE CAPACITOR TO THE MOTOR. BY THE WAY I DID SWITCH OPUT THE CAPACITOR WITH ONE THAT WAS WORKING FINE SO GUYS AND GALS MANANA I WILL REPORT MY FINDINGS. I AM SURE THE WIRES FROM THE CAPACITOR TO THE MOTOR WILL BE THE CULPRIT. I WILL ALSO CHECK FROM THE BOARD TO THE MOTOR AND TO THE CAPACITOR FOR CONTINUITY HAVE A GOOD NITE

Online haroldsappliance

  • Technician
  • Member Since: Nov 2011
  • Posts: 616
  • Country: us
    • Appliance repair
Re: MAYTAG WASHER MODEL MVWC450XW
« Reply #1 on: April 23, 2013, 05:12:50 AM »
With washer off, check that tub moves freely. Had one Recently that had a faulty board. Motor would hum until ol protector opened circuit. Check cap with cap tester.

Offline gregaguilar

  • Technician
  • Member Since: Jan 2012
  • Posts: 95
Re: MAYTAG WASHER MODEL MVWC450XW
« Reply #2 on: April 25, 2013, 11:30:55 PM »
sure enough it was a broken wire from the capacitor to the motor. this wire was taped up from factory so it could not be seen. i connected it up and then when i went to calibrate it i notice that when it was time to agitate it wouldnt do it. to my surprice i had taken a look at the actuator and when reinstalling it i missed the latch to the slutch. man what a dummy anyway i reinstalled the little arm in to the loop of the slutch recalibrated it and its working fine.oh when i first calibrated it the spin led and the lid led would blink on and off when the machine was to agitate.  the slutch was stuck on the spin position even though the actuator was not in the slutch slot. guys this machibne ate my frijoles thanks guys  oh i used my ohmeter from the wires on the capacitor and the other end at the motor and i just kept inserting my real needle probe on the motor end wire until i finally got continuity

 

Maytag Washer Model mav7600aww, noisy

Started by dex

Replies: 1
Views: 4946
Last post October 31, 2007, 05:50:56 PM
by rickgburton
Maytag Washer Model #PAVT234AWW Spin Problem

Started by iceman

Replies: 0
Views: 2190
Last post October 06, 2011, 08:36:46 PM
by iceman
Maytag Washer belt cooker Model # SAV2655AWW

Started by Washaman

Replies: 18
Views: 3252
Last post November 05, 2011, 08:04:18 PM
by Washaman
Maytag Neptune washer model MAH8700AWW

Started by brad

Replies: 11
Views: 7936
Last post May 21, 2012, 06:12:35 PM
by AJ
Maytag EpicZ washer model no.MHWZ400TQ01

Started by brad

Replies: 5
Views: 2320
Last post July 06, 2012, 08:06:31 PM
by AJ
maytag washer service manual MVWC450XW

Started by gregaguilar

Replies: 1
Views: 1143
Last post January 09, 2013, 08:59:48 PM
by JWWebster