Author Topic: Maytag Topload LAT9420AAW S/N 10 won't Fill/Spin on any Cycle  (Read 670 times)

Offline rockinrobin

  • Technician
  • Member Since: Sep 2011
  • Posts: 146
  • Country: us
    • Buy me a beer through paypal
    • Ransom Mobile Appliance Repair Service
I have a Maytag Topload Washer that won't Fill with Water and won't Spin on any Cycle (it doesn't make any noise). :tickedoff:
Could it be the Timer, Lid Switch, Water Level Switch, Pressure Tube or something else?   

Offline theoldstoveguy

  • Technician
  • Member Since: Jan 2008
  • Posts: 1246
  • Country: us
    • Buy me a beer through paypal
Re: Maytag Topload LAT9420AAW S/N 10 won't Fill/Spin on any Cycle
« Reply #1 on: April 03, 2013, 07:42:34 PM »
Lid switch failure sounds right. Without a meter to check that is where I would start. Wiring diagram for that unit.  http://www.appliancepartspros.com/08-wiring-information-parts-for-maytag-lat9420aae.html

Offline rockinrobin

  • Technician
  • Member Since: Sep 2011
  • Posts: 146
  • Country: us
    • Buy me a beer through paypal
    • Ransom Mobile Appliance Repair Service
Re: Maytag Topload LAT9420AAW S/N 10 won't Fill/Spin on any Cycle
« Reply #2 on: April 04, 2013, 11:09:58 AM »
Lid switch failure sounds right. Without a meter to check that is where I would start. Wiring diagram for that unit.  http://www.appliancepartspros.com/08-wiring-information-parts-for-maytag-lat9420aae.html
I thought the Lid Switch was only activated for Agitate, Drain & Spin (not when Filling with Water).
There's power on the Black & White Wires that connect to the Lid Switch.
The Lid Switch has 4 terminal pins, therefore I need to know which 2 pins (or wire colors) that I need to check for continuity with lid closed.

Offline fairbank56

  • Technician
  • Member Since: Aug 2012
  • Posts: 342
  • Country: us
Re: Maytag Topload LAT9420AAW S/N 10 won't Fill/Spin on any Cycle
« Reply #3 on: April 04, 2013, 01:15:53 PM »
  If the internal fuse link is blown, the washer won't fill either. There are 3 sets of switch contacts in there. Normally, with the lid closed, you should have continuity between L1 (black), machine (SW, blue), and motor (yellow). With the lid open, L1 and machine only.

Eric
« Last Edit: April 04, 2013, 01:19:51 PM by fairbank56 »

Offline rockinrobin

  • Technician
  • Member Since: Sep 2011
  • Posts: 146
  • Country: us
    • Buy me a beer through paypal
    • Ransom Mobile Appliance Repair Service
I replaced this Lid Switch Assembly and the Washer has completed the Cycle without any problems.
 :thanks:

 

Maytag A183 washer drains during Spin cycle fill

Started by Louis

Replies: 2
Views: 2046
Last post August 28, 2010, 01:26:03 PM
by JWWebster
Maytag Topload won't Agitate/Spin on 1 Cycle SAV515DEWW S/N 14

Started by rockinrobin

Replies: 3
Views: 656
Last post March 28, 2013, 05:06:59 PM
by rockinrobin
Maytag washer mah4000aww spin cycle

Started by evo100

Replies: 1
Views: 2494
Last post December 25, 2007, 09:41:02 PM
by AJ
Maytag Spin Cycle

Started by Camarocam

Replies: 1
Views: 3836
Last post February 19, 2008, 11:07:58 AM
by AJ
Maytag washer-- got agitation, no spin in spin cycle

Started by PB3

Replies: 13
Views: 11025
Last post March 28, 2008, 09:18:30 AM
by PB3
Maytag Neptune MAH4000AWW burning smell during spin cycle.

Started by ksujason

Replies: 15
Views: 16920
Last post September 14, 2008, 11:46:31 PM
by Repair-man