Author Topic: Kenmore 9113042992 Gas Oven with Parts Changes During Production  (Read 910 times)

Offline stanjunk

  • VIP Member
  • Member Since: Sep 2011
  • Posts: 11
My 1990 Kenmore model 9113042992 gas wall oven has obviously gone through engineering changes that have resulted in use of different, incompatible parts, for different serial number production runs. I ordered an igniter for this oven and found that the Sears recommended part was a Norton flat style. Partselect.com also pointed to the same flat style. My 9113042992 uses the round carborundum type. I finally tracked  down the right part as GE p/n WB2X9154 by surfing the web. My current concern, is, now I've got a bad control board. Engineering changes could have also been made  to the control board. Since the latest igniter wouldn't fit my oven, the latest control board may not fit, as well. How can I get the proper control board if the online parts vendors don't publish the different parts, for each serial number production run, for a model that's been in production for an extended period?

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Kenmore 9113042992 Gas Oven with Parts Changes During Production
« Reply #1 on: March 29, 2013, 07:39:45 PM »
RepairClinic.com shows the correct Ignitor for you model number
After leaving this Earth, "Do you want the smoking or non-smoking section?"

Online theoldstoveguy

  • Technician
  • Member Since: Jan 2008
  • Posts: 1248
  • Country: us
    • Buy me a beer through paypal
Re: Kenmore 9113042992 Gas Oven with Parts Changes During Production
« Reply #2 on: March 29, 2013, 08:56:47 PM »
I would send it to http://fixyourboard.com/ and get it rebuilt. It's no longer available.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Kenmore 9113042992 Gas Oven with Parts Changes During Production
« Reply #3 on: March 30, 2013, 10:19:03 AM »
Fixyourboard has a better warranty than brand new for around $130 last I saw.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline stanjunk

  • VIP Member
  • Member Since: Sep 2011
  • Posts: 11
Re: Kenmore 9113042992 Gas Oven with Parts Changes During Production
« Reply #4 on: March 31, 2013, 06:19:37 PM »
You're a better shot than I am RegUS_PatOff. Good hunting! However, my shotgun surfing did find the part for a lot less than those guys.
I'll think about the rebuild guys. First I'll take a look at the board myself, and see if I can track down components I CAN REPLACE. If I can recognize the relays from an electronics distributor, or MRO, I might replace if a relay went bad. Don't worry about my safety, I used to groom and rebuild electronic warfare systems on the now retired Poseidon nuclear submarine fleet. When they put me on a desk job, my whole day was taken up tracking down obsolete parts in those same boats. This is similar work.

 

Kenmore/GE Gas Wall Oven Model 9113042992 Igniter Problem

Started by stanjunk

Replies: 7
Views: 1306
Last post May 12, 2013, 08:53:58 PM
by RegUS_PatOff
Sears Kenmore Double Wall Oven 24"

Started by tubcust

Replies: 3
Views: 2549
Last post November 09, 2008, 05:03:21 PM
by AJ
kenmore oven

Started by rogerlodger

Replies: 6
Views: 3415
Last post January 23, 2009, 07:48:12 PM
by Kayakcrzy
Kenmore wall gas oven model # 790-30172400 Electronic Oven Control

Started by jamforoush

Replies: 2
Views: 1744
Last post April 23, 2012, 08:33:56 AM
by jamforoush
Kenmore Elite Micro/convection oven

Started by ahab

Replies: 6
Views: 5075
Last post August 10, 2009, 10:57:37 AM
by Repair-man
Whirlpool/Kenmore Gas Oven

Started by MajorApp

Replies: 3
Views: 1450
Last post October 23, 2009, 08:18:26 AM
by PARTech