Author Topic: Whirlpool dryer, WED8300SW1 thermal fuse  (Read 2518 times)

Offline boss96

  • Technician
  • Member Since: Aug 2012
  • Posts: 25
Whirlpool dryer, WED8300SW1 thermal fuse
« on: March 02, 2013, 04:12:56 PM »
Hi guys, need some input on this one. Went out on a service call for this where the drum is not turning. Thermal fuse was open, replaced it, cleaned out the lint both inside and also the vent. Within 10 minutes it failed again with the complaint that it gets hot to the touch.
Went back and also replaced the thermostat and all the other sensors. At that point it seemed to be running much cooler when I would touch the ex. vent tube. Left the house and next day get the same complaint.
At this point I am thinking of the heating element perhaps shorting to the shield or the motor drawing too much current.
What do you guys think?

Offline haroldsappliance

  • Technician
  • Member Since: Nov 2011
  • Posts: 616
  • Country: us
    • Appliance repair
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #1 on: March 02, 2013, 04:19:04 PM »
 O0


Offline boss96

  • Technician
  • Member Since: Aug 2012
  • Posts: 25
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #3 on: March 02, 2013, 04:35:51 PM »
Thanks for the reply.
For curiosity, what is happening, is the element broken and contacting the shield causing a smaller portion of the element to heat up and get too hot?

Offline haroldsappliance

  • Technician
  • Member Since: Nov 2011
  • Posts: 616
  • Country: us
    • Appliance repair
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #4 on: March 02, 2013, 04:45:08 PM »
That's what it sounds like. Remove the wires and check with an ohm meter from each terminal to the housing for continuity.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #5 on: March 02, 2013, 06:45:33 PM »
Did you remove the filter chute? I have had guys buy fuses and come back only to buy more. Problem was the filter chute was clogged like this:
http://appliancejunk.blogspot.com/2011/08/roper-dryer-tune-up.html
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline boss96

  • Technician
  • Member Since: Aug 2012
  • Posts: 25
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #6 on: March 02, 2013, 07:14:50 PM »
Yes, I did.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #7 on: March 02, 2013, 07:18:40 PM »
Ok then you have a bad control thermistor IF the heater is not shorted to chassis. Probably fatigued to the point of overshooting desired cotton temp of 160 maximum. I predict that instead of the control stat working the 250 limit on the heater is cycling. This causes excessive heat and wrinkled to hell and back hot clothes. Seen it.
« Last Edit: March 02, 2013, 07:22:26 PM by JWWebster »
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline boss96

  • Technician
  • Member Since: Aug 2012
  • Posts: 25
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #8 on: March 02, 2013, 07:25:25 PM »
I don't think so as I replaced all the sensors at once on the second trip. This is a 3rd party warranty so I replaced all the sensors.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #9 on: March 02, 2013, 07:43:40 PM »
The only other thang is the Main control then. As the clothes tumble around the control monitors the thermistor and the dryness sensor bars. It is the job of the thermistor to relay back any changes in resistance to the control and that is how it knows to power up the heater. Did ya try yanking out the connections to the brain and cleaning the corrosion of the contacts?
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9393
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #10 on: March 02, 2013, 08:10:01 PM »
JW, you don't think it's simply a faulty heating element as Harold suggested?
Hope you find our site helpful.

Offline JWWebster

  • Technician
  • Member Since: Jan 2008
  • Posts: 8780
  • Country: us
  • SublimeMasterJW
    • Buy me a beer through paypal
    • JW's Sublime Appliance Advice
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #11 on: March 03, 2013, 08:38:55 AM »
I would check the element for shorts first thing. The last thing I always do when I put any appliance back  together is check for continuity between either hot leg on the power cord to frame.
May the hinges of our friendship
        never grow rusty.

About the icons: The beer is tip link, if a tech saves ya some money buy em a 6 pack. The small green square=personal message. The green dot is a link to my web page on appliance repair and other general BS I love to post. The letter sends me email.
I love fan letters! LOL

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9393
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #12 on: March 05, 2013, 10:57:43 PM »
What did you end up finding wrong?  :popcorn:
Hope you find our site helpful.

Offline boss96

  • Technician
  • Member Since: Aug 2012
  • Posts: 25
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #13 on: March 17, 2013, 12:14:57 AM »
Sorry it took so long, this is a 3rd party warranty and they take awhile to send parts (they won't let us supply them ourselves).
I went back out with the new thermal fuse and a heating element. Don't forget I had previously replaced the thermostat and various thermistors/sensors already.
The unit ran for just under 10 minutes and blew the fuse again. Since this the the third try the warranty company will be doing a buyout.
I wish I had been able to get to the bottom of this problem but since it is not cost effective for us anymore...
I still wonder if perhaps we installed a bad thermostat or something...

Offline RegUS_PatOff

  • Technician
  • Member Since: Dec 2007
  • Posts: 1410
  • Country: us
Re: Whirlpool dryer, WED8300SW1 thermal fuse
« Reply #14 on: March 17, 2013, 04:55:14 AM »
did you test to see if the Heating Element was partially shorted to the chassis / ground ?
 
 
After leaving this Earth, "Do you want the smoking or non-smoking section?"

 

3392519 Whirlpool Dryer Thermal fuse (disposable, one time fuse)

Started by AJ

Replies: 0
Views: 4493
Last post May 02, 2009, 09:06:44 PM
by AJ
Whirlpool/Kenmore Electric dryer top thermal fuse blow/wire burnt

Started by Washaman

Replies: 6
Views: 2057
Last post October 12, 2011, 12:54:53 PM
by Washaman
Dryer Whirlpool Thermal cutoff question?

Started by larrywd

Replies: 3
Views: 2586
Last post January 28, 2008, 12:08:14 PM
by AJ
279816 Whirlpool Thermal Cut-Off For Dryer Heating Element

Started by AJ

Replies: 0
Views: 5357
Last post March 22, 2009, 08:38:14 PM
by AJ
Sears Kenmore Dryer thermal fuse blows frequently

Started by garydecker

Replies: 2
Views: 1468
Last post July 30, 2012, 09:17:28 AM
by JWWebster
Whirlpool Duet YGEW9200LQ0 won't start - not thermal fuse?

Started by micg

Replies: 3
Views: 1111
Last post October 21, 2013, 08:22:46 PM
by micg