Author Topic: Microwave Maytag Dead  (Read 3822 times)

Offline lpayne1234

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 8
Microwave Maytag Dead
« on: May 11, 2008, 09:15:05 PM »
New microwave, dead I get 120 volts as far as the relay on board, but no farther. Where can I find a wiring diagram? Could it be a bad relay?
thanks

Model UMC5200BAS

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9480
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Microwave Maytag Dead
« Reply #1 on: May 11, 2008, 09:49:47 PM »
Hi,

I have attached the tech sheet for your microwave.
Have a look at it and see if that help.

Is your microwave under the one year warranty?
Hope you find our site helpful.

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Microwave Maytag Dead
« Reply #2 on: May 11, 2008, 09:58:28 PM »
Does the display on the board light up?
Can you program a time into it like you were going to heat something up, but the microwave oven does not start?

Ohm out the thermo cut-out and check the door switches.

Offline Repair-man

  • Technician
  • Member Since: Feb 2008
  • Posts: 3020
  • Country: us
  • The Virtual Repairman
    • The Virtual Repairmans Appliance Help
Re: Microwave Maytag Dead
« Reply #3 on: May 12, 2008, 03:19:26 PM »
The LV transformer on the PCB board is likely the problem. There is a 5-year warranty on this board if it was bought before 2006 but not before May 2003. Maytag may not release the part to you without proof of purchase, and they usually require that a qualified servicer do the repair.

You may have a difficult time finding this part, a RAS-5200-00. This unit was made by Samsung for Maytag.
« Last Edit: May 12, 2008, 03:24:48 PM by Repair-man »
"It's only expensive if someone else fixes it for you" -
The Virtual Repairman   www.repair2000.com

Offline lpayne1234

  • VIP Member
  • Member Since: Apr 2008
  • Posts: 8
Re: Microwave Maytag Dead
« Reply #4 on: May 12, 2008, 09:00:47 PM »
Thanks everyone, hopefully all this will help. whirlpooltech board does not light up. No time or anything. all thermo cut off checked out ok, also all door switches ck okay.

Offline whirlpooltech

  • Technician
  • Member Since: Nov 2007
  • Posts: 1367
  • Country: us
  • 20 years of experience
Re: Microwave Maytag Dead
« Reply #5 on: May 12, 2008, 09:11:51 PM »
If you have power to the board, but it does not light up then I would say Repair-man is correct.

Quote
The LV transformer on the PCB board is likely the problem.

 

Microwave Oven appears dead

Started by lishmah

Replies: 8
Views: 3595
Last post December 09, 2008, 03:13:44 PM
by lishmah
Maytag Microwave not Heating.

Started by ThunderScout

Replies: 9
Views: 4671
Last post April 03, 2009, 01:01:43 PM
by whirlpooltech
Maytag microwave with no inner glass on door

Started by rego

Replies: 4
Views: 2083
Last post May 09, 2012, 06:16:33 PM
by rego
maytag microwave hood..door wont stay shut

Started by greid4905

Replies: 1
Views: 1812
Last post November 18, 2012, 11:29:22 AM
by tgoods
Maytag Microwave Oven Locks up with 5E or SE fault code

Started by tagarman

Replies: 12
Views: 11489
Last post November 02, 2014, 07:59:25 AM
by macmen22
NEED HELP Maytag Microwave Error Code SE

Started by sgn1122

Replies: 4
Views: 2282
Last post November 05, 2013, 12:40:44 AM
by elgato