Author Topic: Cabrio dryer  (Read 2267 times)

Offline All Brand

  • Technician
  • Member Since: Sep 2010
  • Posts: 70
  • Country: us
Cabrio dryer
« on: December 05, 2012, 03:36:30 PM »
Has anyone have problem with thermal safety's continue to blow.They last about a month. I have checked air flow ,lint screen change the thermistor all operations seem good .They do have a vent that goes down thru flloor with a quick 45 degree turn.Left out to run still blows ? Any suggestions thxs Dave

Online LowSL2

  • Technician
  • Member Since: Dec 2011
  • Posts: 913
  • Country: us
  • Fletch F. Fletch
    • Buy me a beer through paypal
Re: Cabrio dryer
« Reply #1 on: December 05, 2012, 04:43:02 PM »
I have the same problem with my aunts Cabrio dryer. I've put three thermal fuses on it and they keep blowing. I've checked everything. I'm curious if anyone else had encountered this.

No model number because I keep forgetting to write it down...

Sent from my DROID BIONIC using Tapatalk 2

LowSL2
15 Years of Professional Appliance Repair Experience

Offline donsabol

  • Technician
  • Member Since: Dec 2011
  • Posts: 75
Re: Cabrio dryer
« Reply #2 on: December 05, 2012, 07:11:15 PM »
if its electric check to see if element sagging had on that didnt show
up for sometime then found it  grounding outcausing heat to stay on

Offline Blaiser

  • Technician
  • Member Since: Jun 2011
  • Posts: 241
  • Country: us
    • Buy me a beer through paypal
Re: Cabrio dryer
« Reply #3 on: December 05, 2012, 07:37:21 PM »
I would definitely check the duct work, whether internal or exterior. That fuse is blowing because there is a restriction some where. Do some investigating starting from inside the internal cabinet, then blower chamber. You can always run the Dryer (If electric) without the 4" Hose hooked up. DO NOT RUN WITHOUT A VENT LINE ATTACHED IF THIS IS A GAS DRYER (CARBON MONOXIDE)!!But definitely run it with your wifes old stocking attached (to catch the lint) to the back and see if it still blows. That way you can eliminate the exterior duct work theory. I had my own Dryer do the same thing and found out that the little finches birds outside made a little home just inside the wall of the vent line causing a flow restriction. Also any time you have a 90' Degree bend in your vent line that eliminate roughly 8 feet of vent hose of the 40' feet that is maximum run recommended.

Offline scrapiron

  • Technician
  • Member Since: Nov 2011
  • Posts: 147
  • Country: us
  • Service Tech Since 1974
Re: Cabrio dryer
« Reply #4 on: December 05, 2012, 08:49:23 PM »
I've run into probably half a dozen with this problem. The thermal fuse is rated at 90 degrees C. Temps seem to be topping out at 87 to 90 C unvented. Of course the thermal fuse fails. Thermistor was the cause on one, the others were fixed by replacing the control board.

Offline All Brand

  • Technician
  • Member Since: Sep 2010
  • Posts: 70
  • Country: us
Re: Cabrio dryer
« Reply #5 on: December 18, 2012, 02:36:45 PM »
Finally went back to customer out of town .The vent on this unit is 6 feet long with 2 90 degree elbows.Clean no venting problems.I chg the heater just in case it was shorting.It last a mtn maybe 2 them blows.Why would the control board be a factor in this fuse blowing? I have also chg the thermistor originaly thxs Dave
 

Offline domain

  • Technician
  • Member Since: Nov 2012
  • Posts: 1072
  • Country: us
Re: Cabrio dryer
« Reply #6 on: December 18, 2012, 04:29:46 PM »
I am beginning to believe that the main pcb is not reading the thermistor correctly, or maybe the dryer is getting overloaded??? :D

Offline scrapiron

  • Technician
  • Member Since: Nov 2011
  • Posts: 147
  • Country: us
  • Service Tech Since 1974
Re: Cabrio dryer
« Reply #7 on: December 18, 2012, 09:15:39 PM »
Domain is correct, the circuit board is not processing the resistance from the thermistor properly. The board is cycling the heater at too high a temp causing the thermal fuse to fail.

Offline RAH52

  • Technician
  • Member Since: Aug 2008
  • Posts: 716
  • Country: ca
Re: Cabrio dryer
« Reply #8 on: December 19, 2012, 05:13:07 AM »
Can anyone supply a model number
« Last Edit: December 19, 2012, 05:14:01 AM by RAH52 »

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9591
  • Country: us
    • ApplianceJunk.com - Appliance Repair
Re: Cabrio dryer
« Reply #9 on: December 26, 2012, 08:11:35 PM »
 :popcorn:
Hope you find our website helpful.

 

Cabrio Dryer & Diagnotic Test (Standby)Mode

Started by missnaz

Replies: 5
Views: 7147
Last post June 12, 2009, 10:51:05 PM
by JWWebster
L-82 8178584 Whirlpool Cabrio Dryer Service Repair Manual

Started by AJ

Replies: 0
Views: 7502
Last post August 17, 2009, 12:54:41 PM
by AJ
cabrio dryer

Started by crappycabrio

Replies: 17
Views: 5859
Last post March 29, 2011, 02:10:59 PM
by AJ
whirlpool cabrio dryer- "f2" code?

Started by puzzled1

Replies: 2
Views: 5767
Last post May 17, 2011, 10:41:34 AM
by JWWebster
Whirlpool cabrio dryer quit mid cycle ?

Started by kennyb3030

Replies: 1
Views: 1280
Last post March 09, 2014, 09:57:57 AM
by AJ
Whirlpool Cabrio Dryer

Started by app1

Replies: 3
Views: 2142
Last post October 04, 2011, 11:18:22 AM
by JWWebster