Author Topic: wcre6270h1ww shifter/control board  (Read 1277 times)

Offline JPG

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 142
wcre6270h1ww shifter/control board
« on: October 16, 2012, 03:36:05 PM »
HI I have a washer that goes through the cycle fine but at the end the shifter just goes back and fourth  over and over again., clicks consantly at end of cycle. all lights are off on the control panel.
 
Now it can be 3 things main control  panel, motor which has a control board on it or a bad shifter !!!
 
Has anyone seen this before >????
 
 
tks  JPG

Offline bigbuck

  • Technician
  • Member Since: Jan 2011
  • Posts: 953
  • Country: us
  • over 30 years repairing appliance
    • Buy me a beer through paypal
Re: wcre6270h1ww shifter/control board
« Reply #1 on: October 16, 2012, 07:37:25 PM »
Bad mode shifter.

Sent from my MB865 using Tapatalk 2


Offline fairbank56

  • Technician
  • Member Since: Aug 2012
  • Posts: 415
  • Country: us
Re: wcre6270h1ww shifter/control board
« Reply #2 on: October 16, 2012, 08:00:27 PM »

  What do you mean by saying the shifter goes back and forth? The shifter is a cam that goes up (shifter coil energized for agitate) or down (de-energized for spin). Are you saying that it is constantly engaging/disengaging after a normal cycle? Or are you talking about the agitator going back and forth? How long does it do this after normal cycle? Does cycling the power make it stop?

Eric

Offline JPG

  • VIP Member
  • Member Since: Nov 2007
  • Posts: 142
Re: wcre6270h1ww shifter/control board
« Reply #3 on: October 17, 2012, 12:32:47 PM »
hi yes the shifter goes up and down over and over after cycle   there is no agitation, im not sure how long it does it but the lady just unplugs it....    tks  joe

Offline fairbank56

  • Technician
  • Member Since: Aug 2012
  • Posts: 415
  • Country: us
Re: wcre6270h1ww shifter/control board
« Reply #4 on: October 17, 2012, 02:05:24 PM »

  Well, the shifter appears to be working fine. It's just a dumb device, no brains/electronics, just a coil of wire. Current through the coil creates a magnetic field that pulls the shifter cam up. Stop the current and a spring sends the cam back down. The inverter is switching the current on/off when it shouldn't be. The inverter has it's own microprocessor (brains) and program algorithms. I don't think the control panel could be making the inverter do this. Sounds like a bad inverter. Are their any error codes on the inverter? Three flashes = corrupted software. If there's an error code, try resetting. If not, replace inverter/motor.

Eric

 

neptune washer- machine control board repair

Started by inot66

Replies: 7
Views: 4000
Last post July 13, 2013, 10:15:59 PM
by def
22002989 Maytag Neptune Control Board

Started by AJ

Replies: 0
Views: 5233
Last post March 07, 2009, 11:48:25 PM
by AJ
134743500 Frigidaire Front Load Washer Motor Control Board

Started by AJ

Replies: 0
Views: 9748
Last post March 11, 2009, 03:41:50 PM
by AJ
134149220 Frigidaire Front Load Washer Motor Speed Control Board

Started by AJ

Replies: 0
Views: 9366
Last post March 22, 2009, 10:25:04 PM
by AJ
8571359 Whirlpool Kenmore Calypso Elite Washer Control Board

Started by AJ

Replies: 0
Views: 5733
Last post April 06, 2009, 03:02:32 PM
by AJ
134523106 Frigidaire Front Load Washer Control Board

Started by AJ

Replies: 0
Views: 3743
Last post April 14, 2009, 05:41:05 AM
by AJ