Author Topic: Kenmore dishwasher  (Read 1258 times)

Offline spinner101

  • VIP Member
  • Member Since: Feb 2012
  • Posts: 17
Kenmore dishwasher
« on: May 28, 2012, 04:47:58 PM »
Kenmore dishwasher model # 665.17032402, the clean light keeps blinking and the only thing I can get it to do is drain or cancel. When you push the other buttons the indicator light lights up but nothing happens. I guess I need some help on this, a repair manual and a schematic would also be helpful.Thanks

Offline AJ

  • Technician
    Administrator
  • Member Since: Jun 2007
  • Posts: 9309
  • Country: us
    • ApplianceJunk.com - Appliance Repair Help
Re: Kenmore dishwasher
« Reply #1 on: May 28, 2012, 05:04:35 PM »
Hi,

Remove the toe plate below the door and look for the tech sheet.
It will tell you how to run the dishwasher through the diagnostic cycle for testing.

Let us know what you find or don't find.
Hope you find our site helpful.

Offline tgoods

  • Technician
    Moderator
  • Member Since: Jul 2010
  • Posts: 1470
  • Country: us
    • Buy me a beer through paypal
Re: Kenmore dishwasher
« Reply #2 on: May 28, 2012, 07:19:30 PM »
A blinking clean light indicates a fault in the heating circuit.  This usually a bad heater but sometimes can be from the door not closing properly. Press Heated Dry, Normal, Heated Dry, Normal within 6 seconds.  This will reset it and run a diagnostic cycle.  If you have an ampmeter, clamp it on a main power wire before running the diagnostics.  Look for a 7 amp draw sometime during the cycle.  If you don't get a 7 amp reading the heater is not working.  If you don't have an ampmeter, just try running another regular cycle, making sure the door is shut tight.  If the clean light code comes back, there's still a heating problem.  Check for continuity of the heater.
Attached is the tech sheet.

Offline kcincolo

  • VIP Member
  • Member Since: Feb 2012
  • Posts: 3
Re: Kenmore dishwasher
« Reply #3 on: July 04, 2012, 07:30:00 AM »
I am suffering the same problem, and am able to clear the fault with the diagnostic cycle.  However, in operation, the machine is unable to complete a cycle without re-faulting.

I measured the resistance of the heating element (spec is 10-30 Ohms) at 10.6 Ohms.

Is there any way to adjust the trip point of the trigger?

thanks for any suggestions

Offline scrapiron

  • Technician
  • Member Since: Nov 2011
  • Posts: 140
  • Country: us
  • Service Tech Since 1974
Re: Kenmore dishwasher
« Reply #4 on: July 04, 2012, 07:52:29 AM »
That error can be triggered by things other  than a bad element. Right after you run the diagnostic cycle, carefully check the element for heat it should be quite warm. If it's not, check the heat circuit. (element, thermostat, contol board or related wiring) If the element is warm/hot, then the cause is most likely caused by water not circulating over the element  to heat the water. Check for low/no water fill. Should fill to just below the element. Make sure wash motor/pump is running. Check for debris in the wash pump or plugged/broken chopper in wash pump.

Follow us on Google+
 

Kenmore Dishwasher - Doesn't always drain.

Started by yeltu1188

Replies: 1
Views: 3953
Last post September 15, 2007, 10:36:53 AM
by Pegi
Kenmore Elite Dishwasher

Started by sparky823

Replies: 8
Views: 4749
Last post October 11, 2007, 09:16:14 AM
by Pegi
Kenmore Elite Dishwasher Does Not Start

Started by rgletter

Replies: 5
Views: 4789
Last post December 14, 2007, 07:45:52 PM
by rickgburton
Kenmore 665 dishwasher chopper assembly cover

Started by tomnewf

Replies: 2
Views: 7215
Last post January 06, 2008, 10:59:43 AM
by AJ
Kenmore dishwasher

Started by lcsw

Replies: 4
Views: 4974
Last post February 08, 2008, 05:04:28 PM
by AJ
Kenmore dishwasher motor problem

Started by lgmccoy1

Replies: 3
Views: 7458
Last post February 22, 2008, 11:06:24 AM
by RegUS_PatOff